---
title: "LED Pixel Strip System"
slug: led-pixel-strip-system-y71z20
version: 5
htmlUrl: https://led-pixel-strip-system-y71z20.artifactcafe.dev/v5/index.html
reviewUrl: https://artifact.cafe/a/led-pixel-strip-system-y71z20
---
Office lighting kit · Events + LD

# LED Pixel Strip System  
WS2814 RGBW × DSA DMX-to-SPI

What we actually own (checked against Taobao order history), how it wires, how to size a run, and how to put it to work for office events lighting and LD.

Inventory verified 2026-10-03 Not yet bench-tested W/m & IP rating unconfirmed 

[1 · What we own](#own) [2 · Know your reels](#reels) [3 · How it wires](#arch) [4 · Wiring schematic](#schematic) [5 · Sizing calculator](#calc) [6 · Office setup](#office) [7 · Install guide](#install) [8 · What's missing](#missing) [9 · Buy list](#buy) [10 · Open questions](#open) 

## 1What we own

Only completed orders (交易成功) are counted. Three cancelled orders were excluded.

50 m

WS2814 RGBW 24 V strip · 10 × 5 m reels

500

addressable RGBW pixels (10 px/m)

2

DSA decoders → 2 DMX universes → 256 px at full resolution

700 W

24 V power · 2 × 350 W (14.6 A) PSUs

¥1,487

total spent, Jul 26–30 2026

| Item                                  | Variant                      | Qty | Shop  | Date      | Paid    |
| ------------------------------------- | ---------------------------- | --- | ----- | --------- | ------- |
| WS2814 RGBW 24 V strip, 60 LED/m, 5 m | Sleeved 白板套管 · White W       | 2   | 糊糊蝶照明 | Jul 26    | ¥184.00 |
| Same strip                            | Bare PCB 白板裸板 · White W      | 2   | 糊糊蝶照明 | Jul 27    | ¥158.40 |
| Same strip                            | Bare PCB 白板裸板 · Warm-white W | 6   | 糊糊蝶照明 | Jul 28–29 | ¥470.20 |
| DSA DMX512→SPI pixel decoder          | 5-pin XLR DMX                | 2   | 鑫鼎洲   | Jul 26    | ¥384.00 |
| 24 V switching PSU, 14.6 A / 350 W    | Indoor type (监控电源)           | 2   | 糊糊蝶照明 | Jul 30    | ¥290.00 |
| Total                                 | ¥1,486.60                    |     |       |           |         |

### Related control gear we already have

* ~~**4-port DMX512 node** (Hahan SL04)~~: **stolen, Oct 2026.** Replaced by the Pknight CR011R in the cart.
* **Network**: UGREEN 8-port switch (100 Mbps, plenty for Art-Net) and 8 × 25 m Cat5e cables.
* **3-core 22 AWG LED wire**: 100 m bought (part of it stolen). Fine for data and short power hops up to \~3 m.
* **DMX 3-pin XLR cables**: 4 × 1.5 m and 4 × 5 m. _The DSA decoders take **5-pin** DMX, so we need 3→5-pin adapters._

## 2Know your reels

The 10 reels are not all the same. Label them before they get mixed up.

| Group               | Reels | Length | Best use                                                                         |
| ------------------- | ----- | ------ | -------------------------------------------------------------------------------- |
| Sleeved · White W   | 2     | 10 m   | Anywhere dusty, touchable or temporary: floor edges, booth front, outdoor events |
| Bare · White W      | 2     | 10 m   | Inside aluminium channel; crisp white looks                                      |
| Bare · Warm-white W | 6     | 30 m   | Inside aluminium channel; warm ambient and wall/ceiling washes                   |

**Keep white-W and warm-white-W in separate zones**The W chip differs between the two groups, so the same DMX value looks different side by side. RGB mixes match; whites don't. 

## 3How it wires

The strip does not take DMX. It uses WS2814, an SPI pixel chip. A WLED pixel controller turns Art-Net from the laptop straight into pixel data. Our 2 DSA decoders (DMX in) stay available as extra zones.

lightshow on the Mac

or QLC+, xLights, Resolume

Art-Net  
Ethernet

Network switch

UGREEN 8-port (owned)

Art-Net  
U10–U13

Gledopto Elite 2D-EXMU

WLED · 2 outputs · SK6812 RGBW mode

pixel data  
DI → DO

WS2814 RGBW strip

2 runs × 25 m · 500 px

Fixtures: switch → Pknight CR011R (Art-Net → DMX, U1) → fixture chain. Power: each reel has its own fused wire pair straight from a PSU screw terminal (5 A fuse, max 2 leads per screw). The controller carries data only. **Never feed strip power through the controller.**

### Numbers that matter

* **10 RGBW pixels per metre** (60 LED/m ÷ 6 LEDs per pixel)
* **12 W/m max** at full white, so a 5 m reel draws 60 W / 2.5 A (BTF spec)
* **3 wires**: 24 V, data, GND (single data line, 3-pin SM connector)
* PCB is **10 mm** wide, cuttable every 10 cm
* **4 DMX channels per pixel** (R, G, B, W)
* **128 RGBW pixels per decoder**, which is one universe, about 12.8 m
* The 3 SPI outputs share that one universe; they do **not** give 3 universes
* The "900 pixels" in the listing only applies to the decoder's built-in effects

### Decoder facts (from the manufacturer sheet)

* Lists `WS2814 (RGBW)` among 47 supported IC families
* 5–24 VDC input · 3 SPI/TTL outputs · 5-pin DMX
* **IP20**: indoors, or inside a sealed box outdoors
* Built-in RF is proprietary, **not CRMX**

## 4Wiring schematic

How the parts in the cart connect. Reference designators (C1, X1, P1, F1…) are used in the connection list below.

Signal path

Sheet 1 / Art-Net · DMX · pixel data

Ethernet pixel data DMX GND / V− +24 V DC 120 V AC 

C1 Mac · lightshow eth 2.0.0.22 /8 Art-Net out U1 + U10–U13 N1 UGREEN 8-port owned · 100 Mbps unmanaged X1 Gledopto Elite 2D-EXMU WLED · 2.0.0.50 Art-Net in U10–U13 LED type SK6812 RGBW OUT1 ▸ Run A OUT2 ▸ Run B X2 Pknight CR011R Art-Net → DMX · 2.0.0.40 U1 · 3-pin XLR out Cat6 Cat6 Cat6 A1 5 m·50px A2 5 m·50px A3 5 m·50px A4 5 m·50px A5 5 m·50px end B1 5 m·50px B2 5 m·50px B3 5 m·50px B4 5 m·50px B5 5 m·50px end OUT1 OUT2 J1 J2 U10 · px 1–128 U11 · px 129–250 U12 · px 1–128 U13 · px 129–250 DMX 3-pin F1–F8 Existing DMX fixtures daisy-chain, DMX IN → OUT U1 · addr 1–\~160 120 Ω terminator J1/J2 = JST SM 3-pin pigtail → reel input (arrow ▸ DI) X1 OUT terminals: DATA + GND only — never +24 V to strips reel→reel: factory 3-pin connectors, DO ▸ DI WLED: OUT1 = 256 LEDs (250 real + 6 unused) so Run B starts on U12 Not on the cart: Mac with Ethernet (or a USB-C adapter). Data lead X1 → first pixel: keep under \~2 m. 

Power distribution

Sheet 2 / 120 V AC → 24 V DC → reels

Ethernet pixel data DMX GND / V− +24 V DC 120 V AC 

120 V AC NEMA 5-15 16/3 cord BLK→L WHT→N GRN→⏚ P1 BTF 24 V 350 W PSU 14.6 A max AC: L · N · ⏚ slide switch → 115 V DC: V+ ①②③ · V− ①②③ 2 leads per screw max cover AC terminals V+① F1 5A V−① A1 +24V · GND leads 60 W · 2.5 A max V+① F2 5A V−① A2 +24V · GND leads 60 W · 2.5 A max V+② F3 5A V−② A3 +24V · GND leads 60 W · 2.5 A max V+② F4 5A V−② A4 +24V · GND leads 60 W · 2.5 A max V+③ F5 5A V−③ A5 +24V · GND leads 60 W · 2.5 A max one wire pair per reel · 18 AWG (or 22 AWG ≤3 m) · lever nut at the reel Run A: 25 m 300 W of 350 W 120 V AC NEMA 5-15 16/3 cord BLK→L WHT→N GRN→⏚ P2 BTF 24 V 350 W PSU 14.6 A max AC: L · N · ⏚ slide switch → 115 V DC: V+ ①②③ · V− ①②③ 2 leads per screw max cover AC terminals V+① F6 5A V−① B1 +24V · GND leads 60 W · 2.5 A max V+① F7 5A V−① B2 +24V · GND leads 60 W · 2.5 A max V+② F8 5A V−② B3 +24V · GND leads 60 W · 2.5 A max V+② F9 5A V−② B4 +24V · GND leads 60 W · 2.5 A max V+③ F10 5A V−③ B5 +24V · GND leads 60 W · 2.5 A max one wire pair per reel · 18 AWG (or 22 AWG ≤3 m) · lever nut at the reel Run B: 25 m 300 W of 350 W X1 Gledopto power P1 V+③ / V−③ (shared screw) GND BOND · P1 V− ↔ P2 V− (18 AWG) Run B data is referenced to X1 / P1 GND No shared bus wire: every conductor carries one reel (≤2.5 A). Never join P1 V+ to P2 V+. A1–A5 only on P1; B1–B5 only on P2. 

Connection list

Sheet 3 / point-to-point

| From               | To                  | Cable              | Note                                                                    |
| ------------------ | ------------------- | ------------------ | ----------------------------------------------------------------------- |
| C1 eth             | N1 port 1           | Cat6               | Mac lighting NIC, static 2.0.0.22 / 255.0.0.0                           |
| N1 port 2          | X1 RJ45             | Cat6               | WLED → Config → Wi-Fi Setup → Ethernet type “Gledopto”; static 2.0.0.50 |
| N1 port 3          | X2 RJ45             | Cat6               | Pknight static 2.0.0.40, Art-Net universe 1 (set on the OLED)           |
| X2 DMX out         | F1 DMX in → … → F8  | 3-pin DMX          | 120 Ω terminator in the last fixture's DMX out                          |
| X1 OUT1 DATA + GND | J1 → A1 DI + GND    | JST SM 3-pin       | Leave the pigtail's +24 V wire unconnected                              |
| X1 OUT2 DATA + GND | J2 → B1 DI + GND    | JST SM 3-pin       | Same; Run B GND is shared via the GND bond                              |
| A1 DO … A4 DO      | A2 DI … A5 DI       | factory 3-pin      | Follow the arrows; A5 DO unconnected. Same for B1–B5                    |
| Wall outlet        | P1 / P2 L · N · ⏚   | 16/3 cord          | Black → L, White → N, Green → ⏚. Check the 115 V switch first           |
| P1 V+ ①①②②③        | F1–F5 → A1–A5 +24 V | fuse lead + 18/2   | Each fuse lead on its own PSU screw (max 2 per screw). 5 A ATC          |
| P1 V− ①①②②③        | A1–A5 GND           | 18/2               | Return per reel back to a V− screw; lever nut at the reel               |
| P2 (same)          | F6–F10 → B1–B5      | 18/2 + inline fuse | Mirror of P1                                                            |
| P1 V+③ / V−③       | X1 V+ / V−          | 18/2               | Shares screw ③ with A5; board has its own fuse                          |
| P1 V−              | P2 V−               | 18 AWG             | GND bond — required. Never bond V+                                      |

Power-up order

Sheet 4 / first light

**1 · Before AC**PSU slide switch on 115 V. AC terminals covered. Fuses fitted. No reel connected yet.

**2 · Check DC**Plug in P1 only. Meter 24 V across V+/V−. Unplug.

**3 · One reel**Connect A1 power + J1 data. Power X1\. In WLED: SK6812 RGBW, 50 LEDs, solo R/G/B/W to set colour order.

**4 · Build Run A**Add A2–A5, set OUT1 = 256 LEDs (6 unused) and OUT2 = 250 starting at LED 256\. Then Run B on P2, with the GND bond in place before power.

**5 · Art-Net**WLED Sync: Art-Net, start universe 10, Multi RGBW. Lightshow artnet driver → 2.0.0.50, universes \[10–13\].

**6 · Fixtures**Pknight on U1, terminator on the last fixture. `lightshow driver test` each driver.

## 5Sizing calculator

For planning any run. Defaults are one decoder’s worth of strip. Power uses `length × W/m × 1.25`.

Strip length (m)

Watts per metre (full white)

Control mode RGBW per pixel (4 ch) RGB only (3 ch) 

Mirrored copies None (every pixel unique) 2× (same content in two places) 

–

pixels

–

unique DMX channels

–

decoders / universes needed (own 2)

–

PSU watts incl. 25% headroom

–

350 W PSUs needed (own 2)

–

amps at 24 V (raw)

12 W/m is BTF’s rated maximum for this strip. Confirm it with a clamp meter on the bench (see section 5).

## 6Office setup

Indoors, the bare reels work as they are. Start with one reel on the bench, then build out zones.

### What the kit can do today

* **All 500 pixels individually addressable** as two 25 m runs from one controller, e.g. a bar behind the DJ booth and a wall or ceiling line
* The 2 DSA decoders can add mirrored or standalone zones later (DMX in; need 3→5-pin adapters)
* Driven by lightshow’s Art-Net driver, or anything else that sends Art-Net/sACN
* Power: each 350 W PSU covers about **23 m** at full white, so the two cover nearly all 50 m
* Keep warm-white reels and white reels in separate zones

### Bench test, first session

1. Connect one reel, one decoder and one PSU, with DMX straight from the node (3→5-pin adapter)
2. On the decoder, set the IC to `WS2814`, then the pixel count and start address
3. Solo R, G, B and W in turn to confirm the **colour order**
4. Measure current at full white on one 5 m reel, which gives the **real W/m**
5. Measure voltage at the far end of the reel to decide how often to inject power
6. Confirm which node port carries which universe

**Patching in your console**Patch each zone as N pixels of a 4-channel RGBW fixture (R, G, B, W), one universe per decoder. Most consoles and pixel mappers (MA, QLC+, Resolume, Madrix) can then treat the zone as a pixel matrix. 

**PSU safety**The 350 W units are open-frame indoor supplies. Mount them off the floor with ventilation, a fused inlet and a cover over the AC terminals. 

## 7Install guide

For semi-permanent office runs or event builds.

### Wiring

1. One decoder per zone, close to the start of its run
2. Data runs in one direction. Follow the PCB arrows (DI → DO), not the wire colours
3. Inject 24 V at least every 5 m, in a star layout from a fused distribution block
4. Common ground across the PSU, decoder and strip
5. Shielded DMX cable, 120 Ω terminator on the last decoder in a chain
6. Use flexible 3-core jumpers around corners; never fold the strip sharply

### Mounting

1. Bare reels go in aluminium channel with a diffuser; tape inside the channel is fine indoors
2. Sleeved reels: screw clips every 20–25 cm for anything temporary or touchable
3. Don't stick strip tape directly onto bare metal (the listing warns against it)
4. Seal cut ends with heat shrink; add neutral-cure silicone if the run will be outdoors
5. Decoders are IP20: indoors only unless inside a sealed box
6. Mount PSUs off the floor, ventilated, with covered AC terminals

## 8What's missing

Every link from the wall outlet to a lit pixel. "In cart" = on the office Amazon cart (2026-10-04), not ordered yet.

| Link                         | Status     | Covered by                                                                                                |
| ---------------------------- | ---------- | --------------------------------------------------------------------------------------------------------- |
| Kit physically in the office | Check      | Taobao orders went to a Guangzhou forwarding warehouse (转运); confirm they have arrived                    |
| Wall outlet → 24 V           | In cart    | 2 × 16/3 plug cords. **Set each PSU’s 115/230 V switch to 115 V**; make sure the AC terminals are covered |
| 24 V → strips                | In cart    | Inline 5 A fuse per reel, 100 ft 18 AWG + remaining 22 AWG wire, lever nuts                               |
| Mac → lighting network       | In cart    | Own UGREEN 8-port switch + Cat6 ×3 in cart. Mac needs an Ethernet port (or a USB-C adapter, not in cart)  |
| Network → pixels             | In cart    | Gledopto Elite 2D-EXMU: all 500 px over Art-Net                                                           |
| Network → DMX fixtures       | In cart    | Pknight CR011R (3-pin), universe 1                                                                        |
| Controller → strip           | In cart    | JST SM 3-pin pigtails; whole 5 m reels joined with factory connectors, so no soldering                    |
| Mounting                     | Not bought | Optional: aluminium channel + diffuser for the bare reels; clips for the sleeved reels                    |
| Test + measure               | Not bought | Optional: DC clamp meter to measure real W/m                                                              |

## 9Buy list

The cheapest set that makes everything work, in the office Amazon cart on 2026-10-04 (not ordered). Checked against the Taobao order history: the switch was dropped (we already have a UGREEN 8-port). Prices are what Amazon showed that day.

| Ref    | Item                                                                           | Qty | USD   | Why this one                                                                                                                              |
| ------ | ------------------------------------------------------------------------------ | --- | ----- | ----------------------------------------------------------------------------------------------------------------------------------------- |
| X1     | [Gledopto Elite 2D-EXMU](https://www.amazon.com/dp/B0GJZYWVQ7)                 | 1   | 27.99 | Ethernet WLED controller, 2 outputs → all 500 px straight from Art-Net. $7.60 cheaper than the 4-output model, which adds nothing we need |
| X2     | [Pknight CR011R, 3-pin](https://www.amazon.com/dp/B0B1YRTYB7)                  | 1   | 72.99 | Cheapest well-reviewed Art-Net → DMX node for the existing fixtures                                                                       |
| —      | [Cat6 10 ft, 3-pack](https://www.amazon.com/dp/B094Z6CCSF)                     | 1   | 11.99 | One cable per device                                                                                                                      |
| —      | [16/3 plug cord to bare wire, ETL](https://www.amazon.com/dp/B0FKT6242L)       | 2   | 15.98 | Plugs the two screw-terminal PSUs into the wall                                                                                           |
| F1–F10 | [Inline ATC fuse holders ×10 + 70 fuses](https://www.amazon.com/dp/B0DT15YKF2) | 1   | 9.98  | One 5 A fuse per reel; cheaper than a fuse block                                                                                          |
| —      | [18 AWG pure-copper zip wire, 100 ft](https://www.amazon.com/dp/B0CYFQM79X)    | 1   | 22.95 | One pair per reel (≤2.5 A each). Some of our 22 AWG wire was stolen; 100 ft for $7 more than 50 ft                                        |
| —      | [Lever connectors, 50 pcs](https://www.amazon.com/dp/B09CKDWK4Q)               | 1   | 9.99  | Joins at each reel and pigtail, no soldering                                                                                              |
| J1–J2  | [JST SM 3-pin pigtails, 10 pairs](https://www.amazon.com/dp/B0BW777LBK)        | 1   | 6.49  | Controller → reel input                                                                                                                   |
| Total  | 178.36                                                                         |     |       |                                                                                                                                           |

**Add only if needed**PSU enclosure ([$26.90 each](https://www.amazon.com/dp/B0H8SJ926F)) if the PSUs have no clear terminal cover · USB-C Ethernet adapter if the Mac has no port · aluminium channel (Muzata U1SW, \~$25 per 6 m) for looks · clamp meter (UNI-T UT210E, \~$46) to measure real W/m. 

### Alternatives we considered

**Pro pixel controller:** DMXking LeDMX4 MAX ([$360–389](https://shop.dmxking.com/LeDMX4-MAX%5Fp%5F50.html), lists WS2814, RDM) or Advatek PixLite E4-S Mk3 ([$449](https://axionlighting.com/product/advatek-pixlite-e4-s-mk3-pixel-controller/)). Worth it for touring-grade reliability.

**DSA decoders only:** 2-universe Art-Net node (ENTTEC ODE Mk3, [$319](https://www.sweetwater.com/store/detail/ODEmk3--enttec-ode-mk3-two-universe-bidirectional-dmx-ethernet-gateway)) + 3→5-pin adapters. Reaches only 256 px. USB-DMX cables (\~$25) would need a new lightshow driver.

**Don't buy these decoders** `557598721715` is 5/12 V only with no WS2814 support. `872050948865` doesn't list WS2814 on its spec sheet. `579982515902` uses older IC families only. Constant-voltage RGBW DMX decoders are the wrong type for a pixel strip. 

## 10Open questions

* Is the kit physically in the office yet?
* Real W/m at full white (bench measurement; rated 12 W/m)
* Does each reel have 3 wires (expected) or 4? If 4, tie BI to GND at the input
* Real IP rating of the sleeved reels (the listing table says IP20; the product photos suggest waterproof)
* Where do the two zones go in the office?
* Which zone gets white-W reels and which gets warm-white-W?

Source: Taobao order history (read-only check, 2026-10-03) and earlier strip and decoder research.
