Office lighting kit · Events + LD

LED Pixel Strip System
WS2814 RGBW × DSA DMX-to-SPI

What we actually own (checked against Taobao order history), how it wires, how to size a run, and how to put it to work for office events lighting and LD.

Inventory verified 2026-10-03 Not yet bench-tested W/m & IP rating unconfirmed

1What we own

Only completed orders (交易成功) are counted. Three cancelled orders were excluded.

50 m
WS2814 RGBW 24 V strip · 10 × 5 m reels
500
addressable RGBW pixels (10 px/m)
2
DSA decoders → 2 DMX universes → 256 px at full resolution
700 W
24 V power · 2 × 350 W (14.6 A) PSUs
¥1,487
total spent, Jul 26–30 2026
ItemVariantQtyShopDatePaid
WS2814 RGBW 24 V strip, 60 LED/m, 5 mSleeved 白板套管 · White W2糊糊蝶照明Jul 26¥184.00
Same stripBare PCB 白板裸板 · White W2糊糊蝶照明Jul 27¥158.40
Same stripBare PCB 白板裸板 · Warm-white W6糊糊蝶照明Jul 28–29¥470.20
DSA DMX512→SPI pixel decoder5-pin XLR DMX2鑫鼎洲Jul 26¥384.00
24 V switching PSU, 14.6 A / 350 WIndoor type (监控电源)2糊糊蝶照明Jul 30¥290.00
Total¥1,486.60

Related control gear we already have

2Know your reels

The 10 reels are not all the same. Label them before they get mixed up.

GroupReelsLengthBest use
Sleeved · White W210 mAnywhere dusty, touchable or temporary: floor edges, booth front, outdoor events
Bare · White W210 mInside aluminium channel; crisp white looks
Bare · Warm-white W630 mInside aluminium channel; warm ambient and wall/ceiling washes
Keep white-W and warm-white-W in separate zones The W chip differs between the two groups, so the same DMX value looks different side by side. RGB mixes match; whites don't.

3How it wires

The strip does not take DMX. It uses WS2814, an SPI pixel chip. A WLED pixel controller turns Art-Net from the laptop straight into pixel data. Our 2 DSA decoders (DMX in) stay available as extra zones.

lightshow on the Mac
or QLC+, xLights, Resolume
Art-Net
Ethernet
Network switch
UGREEN 8-port (owned)
Art-Net
U10–U13
Gledopto Elite 2D-EXMU
WLED · 2 outputs · SK6812 RGBW mode
pixel data
DI → DO
WS2814 RGBW strip
2 runs × 25 m · 500 px

Fixtures: switch → Pknight CR011R (Art-Net → DMX, U1) → fixture chain. Power: each reel has its own fused wire pair straight from a PSU screw terminal (5 A fuse, max 2 leads per screw). The controller carries data only. Never feed strip power through the controller.

Numbers that matter

  • 10 RGBW pixels per metre (60 LED/m ÷ 6 LEDs per pixel)
  • 12 W/m max at full white, so a 5 m reel draws 60 W / 2.5 A (BTF spec)
  • 3 wires: 24 V, data, GND (single data line, 3-pin SM connector)
  • PCB is 10 mm wide, cuttable every 10 cm
  • 4 DMX channels per pixel (R, G, B, W)
  • 128 RGBW pixels per decoder, which is one universe, about 12.8 m
  • The 3 SPI outputs share that one universe; they do not give 3 universes
  • The "900 pixels" in the listing only applies to the decoder's built-in effects

Decoder facts (from the manufacturer sheet)

  • Lists WS2814 (RGBW) among 47 supported IC families
  • 5–24 VDC input · 3 SPI/TTL outputs · 5-pin DMX
  • IP20: indoors, or inside a sealed box outdoors
  • Built-in RF is proprietary, not CRMX

4Wiring schematic

How the parts in the cart connect. Reference designators (C1, X1, P1, F1…) are used in the connection list below.

Signal path
Sheet 1 / Art-Net · DMX · pixel data
Ethernet pixel data DMX GND / V− +24 V DC 120 V AC
C1 Mac · lightshow eth 2.0.0.22 /8 Art-Net out U1 + U10–U13 N1 UGREEN 8-port owned · 100 Mbps unmanaged X1 Gledopto Elite 2D-EXMU WLED · 2.0.0.50 Art-Net in U10–U13 LED type SK6812 RGBW OUT1 ▸ Run A OUT2 ▸ Run B X2 Pknight CR011R Art-Net → DMX · 2.0.0.40 U1 · 3-pin XLR out Cat6 Cat6 Cat6 A1 5 m·50px A2 5 m·50px A3 5 m·50px A4 5 m·50px A5 5 m·50px end B1 5 m·50px B2 5 m·50px B3 5 m·50px B4 5 m·50px B5 5 m·50px end OUT1 OUT2 J1 J2 U10 · px 1–128 U11 · px 129–250 U12 · px 1–128 U13 · px 129–250 DMX 3-pin F1–F8 Existing DMX fixtures daisy-chain, DMX IN → OUT U1 · addr 1–~160 120 Ω terminator J1/J2 = JST SM 3-pin pigtail → reel input (arrow ▸ DI) X1 OUT terminals: DATA + GND only — never +24 V to strips reel→reel: factory 3-pin connectors, DO ▸ DI WLED: OUT1 = 256 LEDs (250 real + 6 unused) so Run B starts on U12 Not on the cart: Mac with Ethernet (or a USB-C adapter). Data lead X1 → first pixel: keep under ~2 m.
Power distribution
Sheet 2 / 120 V AC → 24 V DC → reels
Ethernet pixel data DMX GND / V− +24 V DC 120 V AC
120 V AC NEMA 5-15 16/3 cord BLK→L WHT→N GRN→⏚ P1 BTF 24 V 350 W PSU 14.6 A max AC: L · N · ⏚ slide switch → 115 V DC: V+ ①②③ · V− ①②③ 2 leads per screw max cover AC terminals V+① F1 5A V−① A1 +24V · GND leads 60 W · 2.5 A max V+① F2 5A V−① A2 +24V · GND leads 60 W · 2.5 A max V+② F3 5A V−② A3 +24V · GND leads 60 W · 2.5 A max V+② F4 5A V−② A4 +24V · GND leads 60 W · 2.5 A max V+③ F5 5A V−③ A5 +24V · GND leads 60 W · 2.5 A max one wire pair per reel · 18 AWG (or 22 AWG ≤3 m) · lever nut at the reel Run A: 25 m 300 W of 350 W 120 V AC NEMA 5-15 16/3 cord BLK→L WHT→N GRN→⏚ P2 BTF 24 V 350 W PSU 14.6 A max AC: L · N · ⏚ slide switch → 115 V DC: V+ ①②③ · V− ①②③ 2 leads per screw max cover AC terminals V+① F6 5A V−① B1 +24V · GND leads 60 W · 2.5 A max V+① F7 5A V−① B2 +24V · GND leads 60 W · 2.5 A max V+② F8 5A V−② B3 +24V · GND leads 60 W · 2.5 A max V+② F9 5A V−② B4 +24V · GND leads 60 W · 2.5 A max V+③ F10 5A V−③ B5 +24V · GND leads 60 W · 2.5 A max one wire pair per reel · 18 AWG (or 22 AWG ≤3 m) · lever nut at the reel Run B: 25 m 300 W of 350 W X1 Gledopto power P1 V+③ / V−③ (shared screw) GND BOND · P1 V− ↔ P2 V− (18 AWG) Run B data is referenced to X1 / P1 GND No shared bus wire: every conductor carries one reel (≤2.5 A). Never join P1 V+ to P2 V+. A1–A5 only on P1; B1–B5 only on P2.
Connection list
Sheet 3 / point-to-point
FromToCableNote
C1 ethN1 port 1Cat6Mac lighting NIC, static 2.0.0.22 / 255.0.0.0
N1 port 2X1 RJ45Cat6WLED → Config → Wi-Fi Setup → Ethernet type “Gledopto”; static 2.0.0.50
N1 port 3X2 RJ45Cat6Pknight static 2.0.0.40, Art-Net universe 1 (set on the OLED)
X2 DMX outF1 DMX in → … → F83-pin DMX120 Ω terminator in the last fixture's DMX out
X1 OUT1 DATA + GNDJ1 → A1 DI + GNDJST SM 3-pinLeave the pigtail's +24 V wire unconnected
X1 OUT2 DATA + GNDJ2 → B1 DI + GNDJST SM 3-pinSame; Run B GND is shared via the GND bond
A1 DO … A4 DOA2 DI … A5 DIfactory 3-pinFollow the arrows; A5 DO unconnected. Same for B1–B5
Wall outletP1 / P2 L · N · ⏚16/3 cordBlack → L, White → N, Green → ⏚. Check the 115 V switch first
P1 V+ ①①②②③F1–F5 → A1–A5 +24 Vfuse lead + 18/2Each fuse lead on its own PSU screw (max 2 per screw). 5 A ATC
P1 V− ①①②②③A1–A5 GND18/2Return per reel back to a V− screw; lever nut at the reel
P2 (same)F6–F10 → B1–B518/2 + inline fuseMirror of P1
P1 V+③ / V−③X1 V+ / V−18/2Shares screw ③ with A5; board has its own fuse
P1 V−P2 V−18 AWGGND bond — required. Never bond V+
Power-up order
Sheet 4 / first light
1 · Before ACPSU slide switch on 115 V. AC terminals covered. Fuses fitted. No reel connected yet.
2 · Check DCPlug in P1 only. Meter 24 V across V+/V−. Unplug.
3 · One reelConnect A1 power + J1 data. Power X1. In WLED: SK6812 RGBW, 50 LEDs, solo R/G/B/W to set colour order.
4 · Build Run AAdd A2–A5, set OUT1 = 256 LEDs (6 unused) and OUT2 = 250 starting at LED 256. Then Run B on P2, with the GND bond in place before power.
5 · Art-NetWLED Sync: Art-Net, start universe 10, Multi RGBW. Lightshow artnet driver → 2.0.0.50, universes [10–13].
6 · FixturesPknight on U1, terminator on the last fixture. lightshow driver test each driver.

5Sizing calculator

For planning any run. Defaults are one decoder’s worth of strip. Power uses length × W/m × 1.25.

–
pixels
–
unique DMX channels
–
decoders / universes needed (own 2)
–
PSU watts incl. 25% headroom
–
350 W PSUs needed (own 2)
–
amps at 24 V (raw)

12 W/m is BTF’s rated maximum for this strip. Confirm it with a clamp meter on the bench (see section 5).

6Office setup

Indoors, the bare reels work as they are. Start with one reel on the bench, then build out zones.

What the kit can do today

  • All 500 pixels individually addressable as two 25 m runs from one controller, e.g. a bar behind the DJ booth and a wall or ceiling line
  • The 2 DSA decoders can add mirrored or standalone zones later (DMX in; need 3→5-pin adapters)
  • Driven by lightshow’s Art-Net driver, or anything else that sends Art-Net/sACN
  • Power: each 350 W PSU covers about 23 m at full white, so the two cover nearly all 50 m
  • Keep warm-white reels and white reels in separate zones

Bench test, first session

  1. Connect one reel, one decoder and one PSU, with DMX straight from the node (3→5-pin adapter)
  2. On the decoder, set the IC to WS2814, then the pixel count and start address
  3. Solo R, G, B and W in turn to confirm the colour order
  4. Measure current at full white on one 5 m reel, which gives the real W/m
  5. Measure voltage at the far end of the reel to decide how often to inject power
  6. Confirm which node port carries which universe
Patching in your console Patch each zone as N pixels of a 4-channel RGBW fixture (R, G, B, W), one universe per decoder. Most consoles and pixel mappers (MA, QLC+, Resolume, Madrix) can then treat the zone as a pixel matrix.
PSU safety The 350 W units are open-frame indoor supplies. Mount them off the floor with ventilation, a fused inlet and a cover over the AC terminals.

7Install guide

For semi-permanent office runs or event builds.

Wiring

  1. One decoder per zone, close to the start of its run
  2. Data runs in one direction. Follow the PCB arrows (DI → DO), not the wire colours
  3. Inject 24 V at least every 5 m, in a star layout from a fused distribution block
  4. Common ground across the PSU, decoder and strip
  5. Shielded DMX cable, 120 Ω terminator on the last decoder in a chain
  6. Use flexible 3-core jumpers around corners; never fold the strip sharply

Mounting

  1. Bare reels go in aluminium channel with a diffuser; tape inside the channel is fine indoors
  2. Sleeved reels: screw clips every 20–25 cm for anything temporary or touchable
  3. Don't stick strip tape directly onto bare metal (the listing warns against it)
  4. Seal cut ends with heat shrink; add neutral-cure silicone if the run will be outdoors
  5. Decoders are IP20: indoors only unless inside a sealed box
  6. Mount PSUs off the floor, ventilated, with covered AC terminals

8What's missing

Every link from the wall outlet to a lit pixel. "In cart" = on the office Amazon cart (2026-10-04), not ordered yet.

LinkStatusCovered by
Kit physically in the officeCheckTaobao orders went to a Guangzhou forwarding warehouse (转运); confirm they have arrived
Wall outlet → 24 VIn cart2 × 16/3 plug cords. Set each PSU’s 115/230 V switch to 115 V; make sure the AC terminals are covered
24 V → stripsIn cartInline 5 A fuse per reel, 100 ft 18 AWG + remaining 22 AWG wire, lever nuts
Mac → lighting networkIn cartOwn UGREEN 8-port switch + Cat6 ×3 in cart. Mac needs an Ethernet port (or a USB-C adapter, not in cart)
Network → pixelsIn cartGledopto Elite 2D-EXMU: all 500 px over Art-Net
Network → DMX fixturesIn cartPknight CR011R (3-pin), universe 1
Controller → stripIn cartJST SM 3-pin pigtails; whole 5 m reels joined with factory connectors, so no soldering
MountingNot boughtOptional: aluminium channel + diffuser for the bare reels; clips for the sleeved reels
Test + measureNot boughtOptional: DC clamp meter to measure real W/m

9Buy list

The cheapest set that makes everything work, in the office Amazon cart on 2026-10-04 (not ordered). Checked against the Taobao order history: the switch was dropped (we already have a UGREEN 8-port). Prices are what Amazon showed that day.

RefItemQtyUSDWhy this one
X1Gledopto Elite 2D-EXMU127.99Ethernet WLED controller, 2 outputs → all 500 px straight from Art-Net. $7.60 cheaper than the 4-output model, which adds nothing we need
X2Pknight CR011R, 3-pin172.99Cheapest well-reviewed Art-Net → DMX node for the existing fixtures
—Cat6 10 ft, 3-pack111.99One cable per device
—16/3 plug cord to bare wire, ETL215.98Plugs the two screw-terminal PSUs into the wall
F1–F10Inline ATC fuse holders ×10 + 70 fuses19.98One 5 A fuse per reel; cheaper than a fuse block
—18 AWG pure-copper zip wire, 100 ft122.95One pair per reel (≤2.5 A each). Some of our 22 AWG wire was stolen; 100 ft for $7 more than 50 ft
—Lever connectors, 50 pcs19.99Joins at each reel and pigtail, no soldering
J1–J2JST SM 3-pin pigtails, 10 pairs16.49Controller → reel input
Total178.36
Add only if needed PSU enclosure ($26.90 each) if the PSUs have no clear terminal cover · USB-C Ethernet adapter if the Mac has no port · aluminium channel (Muzata U1SW, ~$25 per 6 m) for looks · clamp meter (UNI-T UT210E, ~$46) to measure real W/m.

Alternatives we considered

Pro pixel controller: DMXking LeDMX4 MAX ($360–389, lists WS2814, RDM) or Advatek PixLite E4-S Mk3 ($449). Worth it for touring-grade reliability.

DSA decoders only: 2-universe Art-Net node (ENTTEC ODE Mk3, $319) + 3→5-pin adapters. Reaches only 256 px. USB-DMX cables (~$25) would need a new lightshow driver.

Don't buy these decoders 557598721715 is 5/12 V only with no WS2814 support. 872050948865 doesn't list WS2814 on its spec sheet. 579982515902 uses older IC families only. Constant-voltage RGBW DMX decoders are the wrong type for a pixel strip.

10Open questions